Whirlpool Cabrio washer lid lock problems (Fixed)

Whirlpool Cabrio washer lid lock problems

Whirlpool Cabrio washer lid lock problems and Fixes

The Whirlpool Cabrio washing machine is well known for its high quality, efficiency, and performance. However, it is expected to go wrong with all modern Whirlpool Cabrio washer lid lock problems for some time. 

In this guide, we will fix the problem with “The lid lock assembly.”

As we know, the lid lock issue resulted in your washer not spin cycle running. You can’t open the lid after completing the cycle, the cover annoyingly clicking continuously, and many other disturbing problems.

In this article, we recommend fixes for the whirlpool cabrio washer below on lid lock problems and how to fix them.

Recommended fixes for the Whirlpool Cabrio washer lid lock problem

Begin with issues ranging from the lid not opening to continuous lid clicking.

Static or Flea charges on the control panel can be stuck in your washer. The best way to troubleshoot is to reset the washer. Resetting these washers can reset the electrical glitches that are behind the main problem.

How to reset the washer

For resetting the washer, the first step is to unplug the washer from the power socket. Let it rest for 5 minutes after it, plug it in back. That’s all your washer should work correctly.

Below are more common faults, and you can resolve each by this article.

Whirlpool washer lid lock clicking.

It is a common problem in case the lock lid gets out of position if you hear it clicking.

Most of the time, it is likely the lid lock is out of position.

to resolve this issue, jiggle the lid and latch a bit to try and press them back into their place.

After closing the lid and attempting to run a new wash cycle.

If you still click without running a cycle, hold the lid until the second click sounds. 

You will see the washer locks, unlocks, and then locks the lid as a way of testing.

If the lock mechanism works, the washer may be in the back or past stage one, but the lid can go out of position before it clicks into place. If the lid continues with the clicking sounds, skip this testing section.

Whirlpool Cabrio washer lid lock Error codes.

Mostly (when something terrible happened to the washer

), the Cabrio washer displays error codes depending on the exact issue to simplify troubleshooting.

There are the most fundamental error codes of lid-lock, which you can see on your washer display. That code has precisely means and recommended repairs for nearly all Cabrio model washers.

Whirlpool Cabrio washer F5E1 Error code

Error F5E1 means that the lid lock fault and the washer detect the lid as open.

Recommended Solution:

To fix this issue, open your washer, tilt down the spinner tub a little, and access the switch wire harness. Ensure the wire harness is set correctly in place.

Whirlpool Cabrio washer F5E2 Error Code

Error F5E2 usually means that the washer is not detecting the closed lid.

Recommended Solution:

Take the first step to confirm that the lid is down/closed properly.

The lid is closed correctly if you answer yes (after confirmation). Then, check if there is any disruption preventing the lid latch from clicking.

Whirlpool Cabrio washer F5E3 Error Code

This error code says the Whirlpool Cabrio washer lid is locked, and the washer cannot unlock the lid.

Recommended solution:

Check for interruptions in the lock system, such as keeping a weighty laundry basket on the lid.

Whirlpool Cabrio washer F5E4 Error Code

The lid is not open during the cycle. Most of the time, this Error code indicates that the start button is pressed for several continuous processes without the lid being opened.

Recommended solution:

So before further proceeding, empty the washer and take out clean laundry.

In the selected Cabrio washer, the following codes identify the problem with the lid lock system:

F81 – Lid is in the open state

The F81 error code means that the door is in the open state.

Recommended Solution:

To fix this error, ensure you have closed the top lid correctly.

It could be by pressing the start button without opening the lid after two or more consecutive washing cycles. 

F80, F82, F84, F85 dl-Failure of lid lock

This code tells us that the lid cannot lock.

Furthermore, check for obstructions that might prevent the lid from fully sealing.

After that, press the PAUSE or CANCEL button once to clear the code.

F83 DU-Failure to unlock the lid

This error code says that due to excessive weight on the cover, the lid cannot unlocked, and it prevents the lock bolt from retracting.

Recommended Solution:

Again, Check if there is any item on the lid (that is exerting pressure on it), such as a detergent packet or laundry basket, and put them down if it is to get rid of any.

Now,  press the PAUSE or CANCEL button once to clear the code.

The washer lid lock stuck.

If your washer lid lock is stuck, dont use force to open the lid, in which case you will break the lid lock assembly.

In that case, you must stop your wash cycle and drain the water by pressing the power button to exit.

When the washer is draining water completely, press the power button again to release the cover.

Now, try to open the lid. If you cannot open it, Unplug the washer and let it rest for around 5 minutes.

After 5 minutes of rest, plug it back into the socket. It always works for most of the time.

If your lid is unlocking, it’s possible that the lid lock assembly is not working.

Before troubleshooting, make sure that the lid is faulty or not by testing.

First, disconnect the whirlpool washer from the power supply and access the cover lock system assembly.

Confirm that the lid lock wire harness is fully pushed into the control board because it is often the issue- If it exists, remove and reconnect it suitably and see if your washer’s lid will unlock.

First, disconnect the whirlpool washer from the power supply and access the cover lock system assembly.

Confirm that the lid lock wire harness is fully pushed into the control board because it is often the issue- If it exists, remove and reconnect it suitably and see if your washer’s lid will unlock.

If this method does not work, put out the lid switch assembly for testing.

How to do the test:

For testing the lid assembly using an ohmmeter or multimeter, verify that the lid lock resistance readings across the connector pinouts are as follows.

If the readings are different, as mentioned, then it is quite possible that the lid lock assembly needs to be replaced. 

“Lock switch solenoid” measurement is J15-1 and J15-3 resistance 85 to 155ohms, “Lock switch” measurement J15-3 and J15-4 resistance unlocked, “Lid switch” J15-3 and j15-2 and resistance is lid closed=0 ohms.

Replace the whole control board of the Whirlpool Cabrio washer.

If mentioned all methods are not working, then you need, and you should consider replacing the whole control panel.

You can try lid lock bypass.

A temporary fix could be to bypass the lid lock. There are two ways to avoid the lid lock system in almost all Whirlpool washers.

First – Using a Lego and a magnet

1. Put Lego inside the lid striker hole

2. place the magnet on the Lego.

Second – Use of jumper wire

if you own an old model of Whirlpool, there is a possibility that it has a 3-wire or 4-wire lid lock wire harness

READ ALSO >>

Is Your Bosch Dishwasher Flashing Red Light and Not Starting?

How To Reset Whirlpool Washer Touch Screen (Steps To Fix)

Whirlpool Cabrio washer lid lock repair

. The fastest way is by bypassing the lid lock mechanism, as we have done above.

However, it is not desirable to run your washer with a bypassed lid lock mechanism because bypassing the lid lock mechanism can result in your washer running even when the door is open, which is not a good specialty.

“This is an interesting point. Let’s dive deeper into it!” instead of repairing the lid lock. We suggest you get a lid lock assembly replacement.

Whirlpool Cabrio washer lid lock problems – Conclusion

For the most part, resetting your Whirlpool Cabrio washer should resolve any lid lock issues. If the problem persists, try the suggested repairs based on the specific fault.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *