Amana Washer Stuck On Sensing Fill? How To Fix!

Don’t worry If your Amana washer stuck on sensing fill. Through this article, we are sharing some helpful troubleshooting ideas.

Table of Contents

The sensing fill light indicates that your washer is sensing several washer issues. It can be not very pleasant for most users, and we know.

It becomes a concern if the washer stays on sensing for more than 5 minutes.

As a result, in this article, we will give you the best ways to fix your Amana washing machine.

Is your Amana washer stuck on sensing fill? Try these fixes

If your Amana washer has malfunctioned and actually stuck on sensing fill for a long time. Your washer won’t proceed and is not ready to act normally. Try the steps below to troubleshoot it.

1 Method: is to Reset Your Washer:

The most common first solution for Amana washer stuck on sensing fill is resetting it.

Follow below mentioned steps to reset your Amana washer.

Move on to fixing…

Please turn off the washer by unplugging it from the power socket.
Turn on the washer back after 1 minute.
After plugging in the washer, within 30 seconds, open and close the lid 6 times in a single row.

Now, you need to check washer behaves normally and works appropriately again. If it is still stuck on sensing, then move on to 2nd method.

2 Method: Check Laundry Overload

The next step is to check your washer to see if it is not overloaded. When you overload your washer, the washer drum may be unable to move to the next cycle.

Move to on fix:

The first step to fix the overloaded washer is to open the door.

Remove some clothes and close the door of the washer.

The washer should behave normally and continue to do the rewash cycle if it continues to do sensing fill again, move on next fixing method.

3 Method: To Check Blocked Water Supply

Consider checking your washer water supply lines. They could be clogged.

If the water is not coming into the drum of the washer and If the washer is not filling up with water, there is a high chance that the water supply is faulty.

Move to on fix:

Ensure the water valve is turned on correctly. If not, turn it on.
Check kinks and leaks and ensure the required water pressure is received from the washer.
If not, repair and replace them.
After that, check if the washer starts normally again.

4 Method: Check Faulty Water Inlet Valve

If the above methods fail to solve the washer issue, we need to inspect some of the components with a multimeter, and if you see damaged and not working components, replace them.

More often than not, a failing water inlet valve could be why the Amana washer won’t go beyond the sensing fill mode.

The water inlet valve of the Amana washer could become clogged and stuck on the sensing fill if it is defective and clogged.

Move on to fixing…

Inspect the washer inlet valve for clog and replace it.

You must double-check and ensure the water inlet valve is open, allowing water into the washer.

If the water valve is faulty, your washer won’t move cycle and likely will stay on sensing fill.

5 Method: Check Faulty Shift Actuator

The shift actuator is responsible for changing the position to move between the spin and wash cycles of the washer.

But Sadly, If it cannot do that, it’s likely to be faulty, and a defective shift actuator is forcing your washing machine to stay on the sensing fill cycle.

Move on to fixing…

To fix the shift actuator, run a diagnostic (How to run a diagnostic is shared towards the end of this article). After ensuring that the shift actuator is faulty, replace it.

6 Method: Check Lid Switch

We also recommend making sure the lid is fully closed. There are chances that the lid lock is not locking properly, and in this case, it can prevent the washer cycle from starting to the end.

Move on to fixing…

Check the lid switch using a multimeter. If you see no continuity, it has a complete chance of being faulty. Just replace it.

7 Methed: Check Fill Sensor

Stuck on sensing fill might also be due to a faulty “Fill sensor.” It is responsible for maintaining the required water level in the washer; if it is defective, it won’t detect water filling. So, in this case, the washer machine will appear stuck.

Move on to fixing…

Using a multimater test the fill sensor does not make continuity, then Highly likelihood chance it is faulty. If the fill sensor is defective, replace it.

8 Method: Check Control Board Failure

If neither the reset, overloading the issue could be Control board.

If it could be a burn and loose connection, you have to inspect it for damage and problems.

Move on to fixing:

If you get a faulty control board, we recommend replacing it.

9 Method: Check the Water-Level Switch

Most Amana washers come with a water-level technology to monitor the water level in the washer so the washing machine gets the required amount of water.

Move on to fixing:

If the water-level sensor malfunctions, it will prevent water from entering the washer, which will cause of “Amana washer stuck on sensing fill.”

10 Method: Check Blocked Inlet Screen

Remove the hoses from the faucet by turning off the water supply and using pliers.
Place hose ends in a pail to catch any remaining water and Check if the inlet screens are on the back of the water inlet valve.
If you notice they’re clogged, clean them with a brush (you can use an old toothbrush, which will work great), temperate soap, and water without removing the screen.
You can also do so after removing the inlet screens

11 Method: Check for Blocked Water Supply

The crucial and straightforward step to troubleshooting starts with checking the water supply and ensuring it is working well.

If the water supply line cannot supply water to the washer, it will get stuck on the sensing fill.

Move on to fixing:

Ensure the water valve is turned on. If not, turn it on.
If any blockages, kinks, or leaks prevent water from reaching the washer, repair or replace the water supply line.
Once repaired or replaced, check if the washer is getting the required amount of water. If yes, move to the next step.

12 Method: Dirty Washer

Dirty washer: It sounds ironic, but it could be the reason that your washer is stuck on sensing fill. It Happens at times.

Move on to fixing:

You can use Amana’s recommended Affresh to wash your washer and remove dirt. It’s one of the most effective washer cleaners right now.

13 Method: Run a Diagnostic Test

If you still cannot fix the sensing fill problem, you must put your Amana washer into diagnostic mode to discover what is wrong with the washer. To put your washer into diagnostic mode, consult your user manual. The test will show a specific issue code if it finds any error.

How to Run Diagnostic On an Amana Washer?

The diagnostic mode will visible hidden errors and faults, which could be why your washer is stuck.

Follow these steps:

Ensure all lights are switched off and the washer is plugged into the power supply to leave your washer on stand-by.

If you see any lighting up any light, you need to rotate the central knob in a 360-degree anti-clockwise circle to switch them off, and then release the knob on the normal mode.

Turn the washer dial once anti-clockwise and after that thrice time clockwise. One more time anti-clockwise and once clockwise, following exact order.

Wait until your washer gets into the diagnostic mode.

If the all status lights light up, the washer is in diagnostic mode.

Turn the knob one click clockwise and repeat one more time. Press the start button and turn the dial one click clockwise.

Now, your washer should run the diagnostic mode and display any error codes.

Final words On Amana Washer Stuck On Sensing Fill!

Do you have an Amana washer that is stuck on sensing fill? Following the above tips will help you diagnose the problem if you have answered yes.

You will need to hire a repairman if you do not get any results with the suggested fixes.

We hope that your Amana washing machine will be back on track soon.

Also, See>>

Whirlpool Cabrio washer lid lock problems (Fixed)

How To Reset Whirlpool Washer Touch Screen (Easy To Fix)

Amana Washer Stuck On Sensing Fill? How To Fix!